TOOLS AND THE SHOP > GENERAL TOOL AND MACHINE DISCUSSION

Modernizing the Makita 9.6 volt tools

<< < (2/5) > >>

bonneyman:
OK, my first modernization was more an act of desperation rather than need.

When I bought my first Makita drill, I didn't know thtat they had other tools available in that style. Some years ago I discovered they made flashlights. Both pivot head and fixed. I snagged them for cheap, but didn't at that time have any good batteries or chargers. So I set about modifying the fixed light (an ML 900) to run off of 9v transistor batteries. Figured the light was so nice and had good features it would be worth having if it functioned.

I bought about a dozen 9v plug-in harness' and soldered 4 of them in parallel to the contacts inside the light handle. There was just enough room to slide 4 batteries into the handle, so plugged the harness' on and slide the whole kit and kaboodle in there. I probably could have made another pair of batteries it but removing the last pair to swap them out when dead would have been a bit tough. maybe a dental pick would have worked? Anyway four batteries were enough to test the concept. Worked great! That light got carried around in one of the cars - perfect for changing a tire or just finding your keys.
Now that I have actual 9000 Makita sticks this light will be relegated to storage. Good to keep as if times get tough I can always find some 9v transistor batteries lying around to run a flashlight.

Over the years this flashlight has had all my homemade parts, damaged pieces, and repairs done to it. So, it will make a good test bed for my new thread. Oh, the switch went bad so had to replace it with a toggle switch I had in a junk bin. Can  hardly tell it's not OEM!

bonneyman:
OK, first up: a 7.2 volt angle drill. (The following description applies to all the 9.6 volt drills and impact as well. At least those versions I have).
Most all of the new impact drivers and wrenches have a carry hook. Some metal clip attached upside down to the battery pack that allows the unit to be hooked on a waistband or belt and carried. I first saw these in 2018 when working temp at a HVAC company. Everyone carried an 18 volt impact, and carried them on their backside when climbing ladders, etc.
The 9.6 volt Makita's don't have such hooks. They originally came in a metal box, later in plastic boxes. I do remember leather holsters available to carry them on your waist, and my Bucket Boss nylon bucket sleeve has a slot for a cordless drill. So I figure adding a carry hook or belt clip might be the first upgrade to do on one.

All of the drills I've seen (not the flashlights, though) have this hole in the bottom of the handle. 3/16" diameter. I never knew what it was for. If anyone is aware of it's purpose, please let me know.

bonneyman:
I did a fair mount of work hanging off of a ladder, and being able to have the Makita drill handy was a real plus. I fashioned a carry hook out of a piece of stiff wire that was bent in such a way as to allow me to hang the drill off of my jeans pocket. I made it long enough where it couldn't fall out, would let the drill gently swing while climbing and descending, and yet the drill was within easy reach. I "remade" my original wire hook the other day trying to duplicate it from memory.
Here it is installed and in use. Not an exact match, but close enough to my original one that you get the idea. I need to figure a way to attach it to the handle so it can't just pull out. When deployed it's not too obtrusive, and when stored it doesn't interfere with the hand grip.

Of course, the young lad I was didn't think far enough ahead to realize the thing would tear the pants pocket with all that stress right there. But my jeans didn't last long anyway, so, nothing lost.

bonneyman:
For the flashlights, Makita made some snap-on covers for the front out of soft red plastic. Apparently one could use the light with that red cover on to flag down some help in an emergency. I've never used them that way, instead using them as protection for the front lens and preventing scratches.
Still available from on-line supply houses (known as signal caps) for the straight head light, I think I'll try and find similar covers off of sour cream containers and tubes of Pringles chips and make my own covers.  With parts becoming NLA protecting the lens on the front becomes an important issue. The two sizes needed for the 9.6v lights are 2 5/8" (pivot head) and 3 1/4" (straight head).

https://www.ereplacementparts.com/signal-cap-p-12802.html

skfarmer:
i can't say for sure but my guess would be a lanyard hole. either thread one end of a lace through and make a loop and a knot or thread both ends through the hole and making a knot leaving a loop on one side.

Navigation

[0] Message Index

[#] Next page

[*] Previous page